Monday, July 2, 2018

MIlling table update

After running the reverse electrolysis at 2A for a day I have switched it over to 6A.  But it would not hold the current.  Kept cutting out so I put the 10A charger back on and the amp meter read about 5A.



What the table looked like today.





My initial thinking is that I could duplicate the tailstock base by using it as a pattern.  After pulling it apart to examine the base it may be better to make a wood pattern due to draft issues which would need to be patched with body filler.  Maybe better just to make a new pattern more specific to the table based on the tailstock design.

I have made a similar pattern for the mill electronics base plate but it will be better to start from scratch.

One issue I have to deal with is how high to position the table above the lathe bed.   Initial inspection has me thinking I want the table to pass over the saddle.   I may loose a bit of milling height but it should enable the cutters to reach further across the milling table.

If you are wondering what is up with the mill I will tell you.   At this point the plan is to use two nearly identical sized pulleys to get the correct speed at the spindle.   The belt will ride on the motor flywheel rim and a slightly smaller pulley on the mill.   Initially I will try to run it without V grooves on the flywheel.   The flywheel is 6 inches and the mill pulley needs to be something like 5.8 inches.  Need to 2X check that.  Also need to check the gear reduction on the mill.  I have seen 2 conflicting numbers.



Sunday, July 1, 2018

CC RZT 42 Mower Spindle

A spindle bearing is out on the CC RZT.   I figured I would have spindle on something else.  No dice.  This one even uses larger bearings than the craftsman mowers.

The top bearing died and balls must have dropped down into the cavity between the bearing and cut grooves into the spacer.  The spacers and the top bearing race are stuck on the shaft.  I am wondering if tossing it in the burnout oven for a while to free it up.  But how hot and how long.

Originally I was thinking it was a rust bond but the blue color from heat has me wondering.




July 17


Used the hydraulic press with two short bits of bed frame backed up by the press plates.   Stuck the bed frame between the bearing and the hub below it and it worked great.  This worked so well I am going to tidy them up a bit and create a center hole then save them in the wheel pullers!

But the spindle has a slit on top where the pulley needs to go.  Thinking of brazing it so the pulley centers.  Maybe cut down the top spacer to let the pulley ride below the cut.   Maybe between that and the brazing it will work.

And it will give me a chance to try my hand at brazing.

But:  I just remembered that the upper bearing had hogged out the housing.  Time for a new spindle.

But But:  Well I found the housing on my office desk.  So it must have been some other bad spindle housing I melted.  But with the shaft looking the way it does I am sticking with the new spindle.  Keep the old housing as a spare.  Hopefully will never need it.  Best insurance is having one on hand.
Now to put it some place safe.

Brown & Sharp #6 Turret Lathe Turret De Rusting

While I was working on freeing up the milling table I figured I could run the the
turret through the derusting process.   The table was much easier to free up than expected.  But there is no point in stopping this.  This is a two part VBLOG.

Part A



Part B

W A I T for it

Lufkin Bore Gauges


My wife found these at a garage sake.

 She did not know what they were but the price was worth the risk in that they would be useful.

They are Lufkin bore gauges.   Looks like it is good up to about 6 or 8 inches.

I am not sure what the missing part was.

These should be useful for checking cylinder bores.  Set it to the max allowable.   If it is loose in the bore the cylinder is out of spec.



Found an image of the set with the instructions in the lid.


I do not see how the rods can be used more than one at a time.


Thursday, June 28, 2018

Mafreto disassembly






Resetting the anodes for the B&S turret.


The table disassembly is progressing  In this video I finish removing the table from the X axis slide.



Removed the plates bolted to the bottom side of the bed.  Unfortunately the iPhone 6 produced a very jittery video.   I don't know if it was due to the heat, or the fact that I was using a Bluetooth headset to get the audio.   More testing is in order.  But I can't rely on it for the only video.



The milling table and its x slide waiting to go back in the derust tank.

Monday, June 25, 2018

Funky sand and setting up to de rust the milling table

Tried 5% western bentonite in what I tough was blow sand.  It burned.  Tire chuck is for scale.













This bar was made by casting aluminum into a shock absorber tube surrounded by the above sand.  I slit the tube down the side.  The gap sprung open a bit and my cut was nt the best so I tied the tube shut with wire and wrapped it with aluminum foil.   It was a bit of chore to remove the aluminum that escaped anyway.  But once it was gone the tube came off easy enough.  Ready for reuse.   At some point I should try this again and take more care cutting the tube open.

I may use this bit of 2" stock to create a tool for setting the lathe tool height.


Repurposing one of my fancy goldfish tanks for de rusting the milling table.   Had a bit of crud in the valve but that was easily cleaned while it was filling.
















120 gallons of water and 7.5 cups of calcium carbonate aka washing soda.  In time the water will clear.   The table is suspended from the chain.   Sections of steel fence posts are suspended from the electrical conduit.  Initially trying 10 amps.  It that is too much I can swap out the charger for a 6 amp.

To be continued.

The amp meter on the battery charger has been missing for a few decades so I scavenged on off a junked lawn tractor and put it inline.

I was tempted to make a time lapse of the process but apple recently replaced the battery on my iPhone 6 which I wanted to use.  It took too long to restore and upgrade the phone.  Missed the beginning which is interesting so maybe  next time.



This is a shot from the morning of the next day.   I have suspended the table from the cherry picker so I can pull it up to check progress.

Notice that bubbles have mostly pushed the scum away from the area over the table.

Wednesday, June 20, 2018

Order DTI stands off amazon.

Ordered these

Got these which I am returning.

Update:  A return has been started and the item ordered is not on amazon at this time.