A page with SWDweb's video and comments for "My Classic Car" from some years ago.
Where small engines rise from the grave
Follow me on my journey as I attempt to return
abandoned lawn tractors, engines and implements
to working condition.
Friday, June 15, 2018
Sunday, June 10, 2018
Motor for the sand snake ?
Yeah its sort of weird to bring this up when I am so close to first chips on the Master Mill. But someone mentioned them on "Paul's Garage" and I figured it would be a good time to look it over.
Now that the motor I bought for my sand processor has made my lathe happy I need to find another motor. Dug out the pool pump I stashed. Its 115V 3450. Have to pull the pump and other plastic off it to see if its an enclosed motor. I doubt an open frame motor would last long in this application. If its enclosed I will think about speed reduction or keep looking.
Free does have merit
Saturday, June 9, 2018
Master Mill is nearly ready to test
The pulley is complete with the exception of set screws aka grub screws.
To cut the keyway I mounted a sharpened woodruff key in a boring bar and broached it by moving the lathe carriage. Lathe motor off.
There are a few blemishes where I did not machine deep enough to get past the aluminum casting shrinkage. It is better to have the pulley strong and massive than have a perfect complexion.
The plan is to try it without cutting grooves for the poly V belt. This is the one borrow from the air compressor. The pulley was sized to make the belt work. It is approximately 10 inches.
The belt is riding a bit to the inward side of the pulley. I think I can fix that by moving the motor a bit left.
The motor pulley is also a flywheel and a cooling fan. It may look funny but without it the motor may overheat.
What's left is this.
- Drill and tap pulley for 2 set screws
- Clean up the flash in the 6 holes. Sadly it is too large to bolt to the faceplate on the lathe. It will hit the ways.
- Cut and mount wood to cover the top of the electronics mount cast earlier. I read that the heat sink should not be grounded.
- Tighten up the column bolts. Check all bolts.
- 2X check that everything is rotating in the right direction and will not unscrew itself. I may have to reverse the input shaft in the mill so it comes out the other side. That or put a set screw in the motor pulley/flywheel.
- Cable strain reliefs.
Past that everything is cosmetic but the electronics may benefit from a cover and a fan.
Tuesday, June 5, 2018
Machining the 10 inch Master Mill Pulley
EDIT : A Mistake : I chucked the pulley by the hub on the flat side. It was too close to the center and would not stay in alignment especially with cardboard shims between the chuck and hub. Live and learn.
Now comes the important stuff. Cutting the hole and keyway along with cutting the rim down to size
Monday, June 4, 2018
Successfull Tenn Inch Pulley Cast
This is a pulley for the Master Mill. I created this pattern and after 2 attempts at molding it gave up. Today I gave it another try and although I still had some problems with the holes in the disc it resulted in what seems to be a useable casting. It rings like a bell.
I did not use any fancy gating because I knew I had little or no aluminum to spare. A small pouring basin feed the sprue which fed the gate. When I did the pour the metal entered the mold very slowly.
I was thinking I made the gate larger than what you see here. The ruler in the above images is not useful. A better size indication is given by comparing the gate to the pulley rim which is about 1 1/8" wide.
Whatever the cause it may have been fortuitous in that it slowed the molten metal when it filled the fragile mold. Need to work on my sand's green strength.
I am starting to think that if you can't snap the gate off after casting its too large. Yeah that too much of a generality but it is something to think about.
Tomorrow we clean up the casting. The pulley as cast is nearer 11 inches but that is with the draft. Some meat will have to be removed from the rim to get the belt I have borrowed from my air compressor to fit.
I did not use any fancy gating because I knew I had little or no aluminum to spare. A small pouring basin feed the sprue which fed the gate. When I did the pour the metal entered the mold very slowly.
I was thinking I made the gate larger than what you see here. The ruler in the above images is not useful. A better size indication is given by comparing the gate to the pulley rim which is about 1 1/8" wide.
Whatever the cause it may have been fortuitous in that it slowed the molten metal when it filled the fragile mold. Need to work on my sand's green strength.
I am starting to think that if you can't snap the gate off after casting its too large. Yeah that too much of a generality but it is something to think about.
Tomorrow we clean up the casting. The pulley as cast is nearer 11 inches but that is with the draft. Some meat will have to be removed from the rim to get the belt I have borrowed from my air compressor to fit.
Saturday, June 2, 2018
Perlite and Sodium Silicate Cake
After about a week it has sort of dried. Some is still soft so I opted to bake it in the burnout oven at aluminum casting temperature 740C in this case
It came out rock hard or close to it.
Now I need to do some experiments. Make up samples with variations.
These come to mind:
1: I want to make channels to lay the coils in. Preferably with a lip to keep the coils from dropping out. This eliminates the need for retaining wires. In this test I will try using a wood former embedded in the mix. The idea is that the wood will turn to ash as the SS bakes. Now the actual furnace will be made with new SS and not require baking to set. I will have to provide some initial heat to burn out the wood. Styrofoam might be melted out with a torch. So that may be a better choice.
2. Add silica flour to the sodium silicate. Not sure what this will do have some ideas but will not put them down here. Just have to see.
3. Try curing the old SS in a bucket of C02 for a few days. Try thinning out the SS with water. This batch is very thick.
It came out rock hard or close to it.
Now I need to do some experiments. Make up samples with variations.
These come to mind:
1: I want to make channels to lay the coils in. Preferably with a lip to keep the coils from dropping out. This eliminates the need for retaining wires. In this test I will try using a wood former embedded in the mix. The idea is that the wood will turn to ash as the SS bakes. Now the actual furnace will be made with new SS and not require baking to set. I will have to provide some initial heat to burn out the wood. Styrofoam might be melted out with a torch. So that may be a better choice.
2. Add silica flour to the sodium silicate. Not sure what this will do have some ideas but will not put them down here. Just have to see.
3. Try curing the old SS in a bucket of C02 for a few days. Try thinning out the SS with water. This batch is very thick.
Subscribe to:
Posts (Atom)